Skip to main content

VK5ZAG 2 evenings in a row reported my 160m 5W WSPR beacon

Woow !
2010-11-09 19:22 PA0O 1.838148 -26 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-09 19:30 PA0O 1.838148 -19 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-09 19:42 PA0O 1.838148 -20 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-09 19:50 PA0O 1.838148 -23 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-10 19:38 PA0O 1.838148 -23 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-10 19:46 PA0O 1.838148 -26 0 JO33hg 5 VK5ZAG PF84vf 15788 83

2 nights VK5ZAG was on 160m WSPR  both nights he received me  at the best gray-line time coincidence?
 
Almost zero activity in Africa Asia S.A.  I just wonder what would be possible if there where a few  VK ZL Oceania active.  Now almost exclusive EU and USA on WSPR Top-band!  
I was on ON4KST low-band chat trying to raise some attention to the DX crowd but got almost no response. Only one HAM wanted to try it but his PC was out of order...
It is very strange that almost no one of the Top-band dxers´s pay attention to this mode. This is a real dx mode!  Around the time  VK5ZAG  decoded me  the classic DX crew could not raise any real dx  using full power CW...  
I just wonder  why do the om's not start  WSPR  mode when they are in "idle" mode?????
 You could  go out , have dinner join your family  and same time leave your dx-station in WSPR running.
The real DX'r  just won't do that. They don't take WSPR serious?   But WSPR is the best propagation or antenna test available for the DX interested hams. Signal reporting is much more accurate and comparative then the normal wet finger reports that are exchanged in  high QRM/QRN. Further more there is no such thing as worked before in WSPR as long as there is propagation every signal is reported and stored in database for later evaluation. The best propagation research available in the history of Radio!  All with low power.  
Is the argument that WSPR is a complete PC controlled mode ?   Correct but  what is left of the DX community when all PC assisted operations in the shack are abandoned?  Of course only paper logging.  Switch of the PC ,DX cluster , DX-chat box. And go complete naked again....
Of course a WSPR "QSO"  is something else as a man made CW QSO but for the propagation antenna test WSPR is much more effective and it can be run 24x7x365
I think WSPR is also very good for 6M  some say it does not fit the magic band because of the short openings.. I doubt that, what about 160m QSB? sometimes no more then 10seconds a dx is workable.
With WSPR more propagation is catched for sure. Because only the most fanatic DX' r stay around all the time. And then go out for some absolute necessary shopping or trying to be a bit social (....)  come back and find out some opening was missed...
I was on 50Mhz WSPR last summer but there is 1 problem NO ACTIVITY!  just no activity or  the typical DX-ham species is very conservative?  Else one would be amazed by what is possible if more hams on DX-locations would run WSPR beacon mode when not in the shack. 

here are the unique call reports  of last week
2010-11-09 19:22 PA0O 1.838148 -26 0 JO33hg 5 VK5ZAG PF84vf 15788 83
2010-11-06 22:48 PA0O 1.838101 -25 0 JO33hg 5 W4ENN EM64ru 7169 295
2010-11-09 22:20 PA0O 1.838148 -25 0 JO33hg 5 WB8HWF EN80sc 6497 296
2010-11-06 22:20 PA0O 1.838100 -24 0 JO33hg 5 N3CO EN72et 6468 300
2010-11-09 03:50 N3CO 1.838164 -30 0 EN72et 5 PA0O JO33hg 6468 45
2010-11-06 21:46 PA0O 1.838099 -18 0 JO33hg 5 WB0IQK EN90dw 6386 296
2010-11-08 03:36 PA0O 1.838042 -27 0 JO33hg 5 WA3USG FN10le 6162 293
2010-11-08 23:04 PA0O 1.838047 -28 0 JO33hg 5 VE3DSH EN93rl 6121 298
2010-11-12 01:28 PA0O 1.838147 -24 0 JO33hg 5 AG6T/3 FN21jc 5980 292
2010-11-09 03:34 PA0O 1.838142 -25 0 JO33hg 5 K2QL FN22ca 5946 294
2010-11-06 21:46 PA0O 1.838099 -20 0 JO33hg 5 N2NOM FN22bg 5933 294
2010-11-08 02:18 PA0O 1.838042 -26 0 JO33hg 5 VE2UG FN35gs 5532 296
2010-11-09 19:22 PA0O 1.838147 -22 0 JO33hg 5 4X1RF KM72ls 3201 124

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het