Skip to main content

Back from Egypt

I was 2 weeks in Egypt again for  QRL reason.
We stayed 50 s-east of Baltim  close to the Mediterranean coast.
http://looklex.com/egypt/baltim.htm   
Thousands of hand build  dows sailing boats can be seen there.
These boats are  unique. The Egyptians are decorating their trucks boats and Tuk tuk's  artistic  xtremely.   
This region is the coolest part of Egypt.
It can be very cool here  but this time it was nice  15 -20 mostly.
Sand beaches  and dunes.   And inland farmer land typical for the Nile delta. This land is almost wetland partly it has some elements in common with our country.
But still waste is dumped along roads and canals like 20 years ago. I would say a primary task of the new Egyptian government would be to clean up this.  I fact the people here live very close with nature  as we did hundred years ago. Also we did dump our waste like this.
But now we have plastics with long recycle time and plastic junk is covering unused land everwhere. Also in Maroc i have seen fields covered with plastic.

Radio wise this must be a super location  but i have not met or seen any radio hams here.
I imagine to set up an WSPR beacon here..
But  i need some local Ham.  Just there seems no hams in this area.
Cairo and Alexandria  is a completely different world.
I let my home radio running all the time.

Very stable  WSPR + XP  on-time is 1 month now i think.
Good results  80m almost every evening VK7DIK reports me

And  15 10 have been open to VK often.

I missed 4A4A  expedition.


Comments

PE4BAS, Bas said…
Hallo Jaap, buiten SU1KM hoor je eigenlijk nooit een radioamateur uit Egypte en omstreken. Denk dat de hobby ook meer voor de rijkere landen is. 73, Bas

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het