Skip to main content

OZ7IT +3 in WSPR tropo 50.293MHz

Now I am the owner of the tiny Flex-1500 .


This is not only a small transceiver but also a spectrum-analyser.

I   have it running with WSPR   using 
VAC  Virtual audio-cable
©  Eugene V. Muzychenko

  and Virtual Serial Port  VSP Manager
© Steve Nance K5FR 
Only the  USB cable to the  PC   / Laptop is needed.
Audio and serial port are virtual connections by software.  

The 1500 has USB  no Fire-wire  this is a bit critical but with some tweaking in the configuration  I hope to get it stable over long time.

Same way it can be connected to N1MM which I did not do yet.


I was surprised  by its sensitivity at 50MHz.  A preamp gave no improvement on reception of the beacons.
ON0SIX LX0SIX  OZ7IGY
The Signal level meter is the best I have ever seen. Weak signals stil have a clear level reading 0-10db over the noise band.
The Pan display shows all. I do have to read the manual there are many more options to find out.


I let it run WSPR    Good signals from OZ7IT  +3dB RX 
my signal -2  with 5W  ( I measure 6W out )
A second WSPR signal in range is  M1DUD JO02 constant copied.


Not much of DX so far...
But 28MHz  still wild   no DX limits is seems 

This morning again ZL2RF 28MHz my 1W 11 decodes
New one for me  WA2YUN  in RK39hh  "only" 11718km
But the propagation to JA  was a bit faded. Or I was too late to switch bands ..


Tonight heard K3ZM 1.825MHz  early   Called with 5W he gave 569
1W was possible too he was extreme strong for 160  clean 599 on the GP and 579 on the loop !





Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het