Skip to main content

28MHz DX even with low Sun spots. South Shetlands active!

R1ANF   South Shetlands GC07mt   many decodes today
After VK0TH my most Southern WSPR entry.
Hoping for DP1POL or  KC4AAA Amundsen Scott  in grid JA00AA to show up again.

unique spots of today 


TimestampCallMHzSNRDriftGridPwrReporterRGridkmaz
 2012-04-27 08:40  VK3AMW  28.126122  -21  0  QF22ir  5  PA0O  JO33hg  16355  313 
 2012-04-27 07:34  VK2KRR  28.126144  -24  0  QF34mr  20  PA0O  JO33hg  16351  316 
 2012-04-27 14:10  RI1ANF  28.126112  -24  -2  GC07mt  5  PA0O  JO33hg  14056  43 
 2012-04-27 14:54  PA0O  28.126071  -25  0  JO33hg  1  RI1ANF  GC07mt  14056  212 
 2012-04-27 08:16  VK6ZRY  28.126050  -20  1  OF78wd  5  PA0O  JO33hg  14032  316 
 2012-04-27 17:20  PA0O  28.126076  -21  1  JO33hg  1  CX2ABP  GF15wc  11512  229 
 2012-04-27 14:06  V53ARC  28.126159  -16  -1  JG87  1  PA0O  JO33hg  8486  354 
Total  29 spots > 8000km   
That means  my self declared DX index = 29   of 100 spots
(>4000km outside EU) 


 Topband  3 days in a row I heard and was heard by ZL3NW 
in CW  tonight also ZL3IX heard but too weak and short for 2-way.
and   VK2KRR  and VK6DZ in WSPR mode  not bad at all
But tonight it ended early Sun is still eruptive.


I heard that V53ARC was copied in Italy at 50MHz WSPR
There will be a day that even in VP8 one will start a WSPR beacon..




Slowly WSPR gets recognized by DX'rs   on 50MHz  too   that is not realy for us here in the 50MHz dead zone but  for TEP and DXpeditions  that have a set for 6m  it is interesting to run an intelligent beacon that can be monitored full time. 

Comments

VE9KK said…
Good morning, I like to use WSPR to see how the bands are doing. Along with the reverse beacon network you can get a good idea how things are out there.

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het