Skip to main content

DL 6M digimode TX is allowed now

Finally we had a clear sunny day. But we are experiencing  the coldest May since 1901!
The temperature can go to minus C  tonight! crazy cold 23 May almost June. 

Newly  DL got permission to transmit in digimodes at 6M.
And also they are allowed to go below 50.085  MHz
Still the power is limited to 25erp only
But that was absolute no limit to the DX  results of some HAMS...

 
F  can use the whole 50-52MHz now


1904 -19 -0.2  50.294553  0 DF9CY JO54 33    my first DL decode.
Hope for more action at 6m  now with lots of well equipped HAMS in DL to TX WSPR  6m.




tonight heard  50001.6  Z21SIX in KH52nd very weak but ID copied
If that was a WSPR beacon it would be reported easy. 

Last year June 6M WSPR was going few evenings stateside

120625 2228  23  -7 -0.4  50.294520  VE1JF FN74 57    
120628 1854   3 -27 -0.6  50.294471  KA1MDA FN32 37
120628 1906  14 -15 -0.5  50.294471  KA1MDA FN32 37
120628 1922  11 -18 -0.6  50.294471  KA1MDA FN32 37

best day June 28 2012  7 decodes
WSPR keeps track of all decodes  but  the WSPR.ORG  database does not keep all decodes that long it is limited.
So only my decodes can be traced back


3B8CF  again worked in JO33 square

No sign that A92IO will ever be back again. Only short skip signals at 4M.



Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het