Skip to main content

ARRL CW this weekend

W.A.S.  at 28MHz  in one weekend is possible when propagation holds like it was this evening

4W QRP  from CA  CW  after some calls 

unmistakable this will be an ARRL-contest participant now playing at 12M
 TI5/CT1ILT  

http://www.qsl.net/pa0oos/2014/ti5_ct1ilt_12.mp3


WSPR today 28MHz  100+ over 7000km

list of unique decodes


TimestampCallMHzSNRDriftGridPwrReporterRGridkmaz
 2014-02-14 07:14  PA0O  28.126183  -26  -1  JO33hg  5  VK7BO  QE38mo  16805  82 
 2014-02-14 06:46  VK2HLG  28.126090  -22  0  QF56og  5  PA0O  JO33hg  16485  319 
 2014-02-14 06:50  PA0O  28.126158  -26  0  JO33hg  5  VK2HLG  QF56og  16485  66 
 2014-02-14 08:28  VK2EMA  28.126076  -5  0  QF37qs  5  PA0O  JO33hg  16124  319 
 2014-02-14 08:32  PA0O  28.126174  -18  0  JO33hg  5  VK2EMA  QF37qs  16124  69 
 2014-02-14 08:08  PA0O  28.126162  -27  0  JO33hg  5  VK5EI  PF95gc  15771  81 
 2014-02-14 09:00  PA0O  28.126169  -28  0  JO33hg  5  DU1MGA  PK04  10251  62 
 2014-02-14 07:48  JG1KGS  28.126071  -18  0  PM95tg  2  PA0O  JO33hg  9178  334 
 2014-02-14 08:12  PA0O  28.126168  -25  0  JO33hg  5  JG1KGS  PM95tg  9178  37 
 2014-02-14 08:38  JE3UBC  28.126082  -21  0  PM74mp  5  PA0O  JO33hg  9049  332 
 2014-02-14 07:38  PA0O  28.126176  -30  0  JO33hg  5  HS0ZKM  OK03gr  9045  79 
 2014-02-14 06:58  HS0ZKM  28.126112  -21  0  OK03gr  5  PA0O  JO33hg  9045  323 
 2014-02-14 07:14  PA0O  28.126155  -20  0  JO33hg  5  JR0GFM  PM96cw  8955  37 
 2014-02-14 18:10  N6KOG  28.126035  -20  0  CM97gs  1  PA0O  JO33hg  8729  29 
 2014-02-14 15:58  PA0O  28.126198  -28  0  JO33hg  5  KE5HPY  EL29  8139  297 
 2014-02-14 15:18  K7UEB  28.126017  -12  0  DN06tb  5  PA0O  JO33hg  7803  31 
 2014-02-14 15:58  PA0O  28.126131  -21  0  JO33hg  5  W6OHM  CN87wp  7797  326 
 2014-02-14 15:54  WA5ETV  28.126080  -16  0  EM15jm  2  PA0O  JO33hg  7734  38 
 2014-02-14 15:46  PA0O  28.126169  -13  0  JO33hg  5  WA5ETV  EM15  7729  302 

Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het