Skip to main content

SONY NXP FM super tuner hot on EBAY


XDR  S3HD




De hele tuner bestaat uit een paar simpele filtertjes.
De 2 NXP ( PHILIPS)  chips bepalen de eigenschappen.

and inside you'll find the NXP TEF6730/SAF7730 radio chipset and several adjustments. The HD module contains an SAF3550 processor and a 16MB SDRAM.

een zeer goede review hier
http://ham-radio.com/k6sti/xdr-f1hd.htm


The XDR-F1HD uses advanced digital signal processing algorithms to dramatically improve reception of FM signals corrupted by noise and interference.
Threshold extension suppresses the impulse noise ordinary FM detectors generate for weak signals. The obtrusive character of this noise quickly degrades reception quality as the signal level falls below a threshold. The impulses arise from detection-vector phase reversal due to additive noise peaks. High-performance satellite and terrestrial microwave FM links have long used various threshold extension techniques to enhance performance. Tracking filter detectors that may extend the threshold occasionally have appeared in consumer FM broadcast tuners.
Adaptive noise reduction forms a filter that tracks the spectrum of the L−R stereo signal. The filter suppresses noise between and beyond spectral peaks without restricting program bandwidth. It also suppresses co-channel interference and multipath distortion, factors that can limit reception quality for stronger signals. The technique takes a big bite out of the 23-dB S/N penalty that has always bedeviled FM stereo reception. Remastered legacy recordings use adaptive noise reduction to suppress surface noise and tape hiss. This may be the technique's first appearance in consumer audio equipment.
Adaptive digital IF filters eliminate adjacent-channel interference in nearly all cases. The filters have flat passbands with extremely steep skirts. The DSP rapidly swaps filter coefficient sets while retaining state variables to dynamically adapt the filter bandwidth to modulation level and interference without introducing switching artifacts. The digital filters are much more effective than conventional analog IF filters. In addition, they do not have the unit-to-unit variation that necessitates ceramic filter selection or tuned compensation for optimal performance. Finally, the symmetrical finite impulse response provides constant group delay. This prevents the audio distortion that group-delay variation in analog filters causes.


Word beschouwd als de beste FM tuner ooit.  
Andere top tuners komen niet in de buurt van de waarden voor selectiviteit en gevoeligheid van ontvangst van zwakke FM Stereo signalen.
Puur door zeer goede software bewerking van de FM stereo signalen.  Niet eens een laag ruisgetal   ca 7dB 

Helaas niet meer in productie.
Op Ebay is het een hot item de prijzen zijn  veel hoger dan de oorspronkelijke 99$
Ik kwam daar pas een beetje achter toen Gerard PE1BBI  zijn FM DX radio mee had in het weekend van de ARRL10

Zelf heb ik een SANSUI  TU717  ik dacht altijd  dat dat een hele goede was.
Maar eigenlijk wordt het me nu pas!  duidelijk waarom de ontvangst van zelfs lokale zenders in goede stereo kwaliteit vaak al lastig en behelpen is. Slechte tuners het kan veel beter. 


NXP heeft wel opvolgers
http://www.nxp.com/documents/leaflet/75017318.pdf

De TEF664X    combineert  TEF6730 SAF7730  in 1 lijkt het
of die net zo goed is?  

Ik ken geen tuner met deze chips.




Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het