Skip to main content
 4 decodes of WD2XSH/17  all -29

 2017-03-06 01:26  WD2XSH/17  0.475648  -29  0  FN42pb  0.1  PA0O  JO33hg  5630  49 
 2017-03-05 23:04  PA0O  0.475602  -30  0  JO33hg  0.2  SV8RV  KM07ks  2042  142 
 2017-03-05 22:58  PA0O  0.475602  -25  0  JO33hg  0.2  SV8RV/1  KM07ks  2042  142 
 2017-03-05 22:10  PA0O  0.475601  -27  0  JO33hg  0.2  EA7HPM  IM67xj  2017  214




QTX  and IRF540Z  ( my last one  i smoked 9)
 this version has about 2500 pF  G-S 
It can run at 5A 22V   with the highest output sofar
but at 100W input level everything heaths up coils and IRF
the antenna current meter  relative  60-70%  
must be close to  100W  rf 

the standard IRF540 measured 2700pF
this one is second best   about  antenna  50%
it is very critical in tuning  the IRF540 starts in self oscillating mode  then the output and current
sudden drops to very low

I can get 100W level with the QTX but on the edge  and only with the Z version of the 
IRF540   still have to fine tune with a piece of ferrit to have max out and good pulseform
it is not  plug and play this QTX  it needs fine tuning and some C values differ a lot with the original
i had to use  C2 C3  15 + 15 nF   and the loading C is 10nF + 6n8 
plus a fine tuning of L3 with a ferrit rod is needed.
Until now every day i saw a different output and or tuning..
The type of IRF makes a lot of difference
This season only one time my QTX was decoded by WD2XSH/17


I know I should have build a heavier PA  that is less critical ?
Awaiting mosfet drivers TC4422 type that can drive the IRFP4227 a heavier type FET


I tried the IRF510  this version has the lowest G-S capacitance of the 3  about 400pF measured
So this  IRF510 should be the most usable RF amplifier 
  But no output with this setup  and worse in standby receive the IRF510 still draws elevated bias current  0.040   The other IRF's do not have this leak current.
  this generates 4-5 S units noise in receive

                                          QTX  IRF540Z   22V 4.5A 
                                         h=50V/dev  Drain pulse 125V  output 370V tt  # 132V eff 


 

Comments

Post a Comment

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit
8 comments
Read more

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir
11 comments
Read more

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het
3 comments
Read more