Skip to main content

23cm tropo

Very good tropo over North Sea  direction N-E  last night  in  SW  all beacons normal level
  My first  LA  with new 23cm station     since 30 years..
 very strong radar sweeps but my new 23cm RX did handle it without problem

jo33hg up to s9 tks Jan
PA0O LA3EQ1296200
2037z 01 Jun
LA3EQ PA0O12962002032z 01 Jun


 tried with    LA4ANA        no copy  too far inland           JO59CU

no one else !

heard again
 LA1UHG  1296.852 MHz   JO59fb     long time S9
 OZ7IGY    1296930             JO55WM   S9+
GB3MHZ    1296830            JO02PB     normal S4
PI7ALK       1296915            JO22IF
PI7QHN        1296.906          CM53b ..
ON0TB        1296.950           JO30BM
DB0XY        1296.913          JO51EU
DB0VC         1296.920          JO54IF
PI6ASD         1296.637          CM55    linear transponder

new heard
SK6MHI     1296.800           JO57TQ
SK7UHI      1296.805           JO57TX
OZ1UHF      1296.955           JO57GH
OZ1SHF      1296.900          JO45WX
DM0UB       1296.850           JO62KK           CW on/off keying   carriers with stepping power
GB3NO        1296.700           JO02PP
PA0O GB3NO12970000637z 01 Jun

   TY2AC   50.102  heard  workable signal CW 2 short  openings  deep QSB
       to late back at frequency after the QRX  i lost patience for DX-ing

   JT65  only single hop ES   EU signals  not a whisper of the DX worked  in other parts of EU


Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het