Skip to main content

WSJT-x multiple instance


I am testing with 2 instances  WSJT-x  latest version.
Using N3IZN notes on gougle.groups.com/forum/#topic/2-meter-wspr/oONMxyALMTO
This is simple using  2 shortcuts to WSJT-X   with  command line  option --rig-name=xxxx
This command line option creates separate program environments with different configurations.


2 (or more)  rigs can be used simultane with WSJT-x  at the same PC
A second instance of WSJT-x  for the 2nd Rig  and the logging is needed
\
The shortcuts to WSJT-x  have to be modified to accomplish this.

to add a second separate working instance for WSJT-x
make a copy of the first shortcut to WSJT-x

rename the shortcut to rig2       rig2  is the name you want to use for your rig

r-click on this WSJT-x rig2
open properties
change the target name to
C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=rig2
( 1 space between wsjtx.exe. and --rig-name=rig2    and rig-namem must be the same rig2 

that is all
if this shortcut is used,  the latest installed WSJT-X  wil be started for rig2  in its separated environment for logging
the location of the rig2 log files can be found menu file -> open log directory


Here  the IC706  is  the 1rst Shortcut
name:  wsjtx - IC706
 target name:
C:\WSJT\wsjtx\bin\wsjtx.exe --rig-name=IC706
Unchanged start in  C:\WSJT\wsjtx
The IC706 is as before connected  hardware with com1 and audio ports

aded 2nd instance
WSJT-X TS2000     using FlexRadio Power-SDR   v2.2.3 emulating radio TS2000
connected  with Flex1500   at USB 474.2kHz
using VAC and V-serial ports
fttb only receive i have an issue that cable1 VAC is used for in and output at P-SDR to let it receive
normally  VAC in is connected to out  and vice versa  but that did not work yet so tx will be not possible this way?

It is running on an older X60 Lenovo with docking bay com1 lpt1 mny USB   and Win10

Now  I can independent operate 474.2kHz  and 6m or 2m
but this system does not run as stable as the classic IC706 WSJT-X over hardware connections



it  crashed few times
do not know what causes the break downs

no crash  after update to Power-SDR 2.8

no DX at 474.2  and 10m is quiet to the good propagation of last weeks has ended


RI1ANO   was very loud at 30M FT8  no others dx heard

the very good Oktober propagation  ended 10m 12m closed now and the low bands very poor
not seen AA1A at 474.2 for days ,  P-SDR setup with the Flex1500  is suffering  software instability
This morning again the SDR RX was frozen


Comments

Archive

Show more

Popular posts from this blog

2011-01-22 DIAMOND 2m 70cm 1m30 Colinear inside

Having relative poor signals on the local 70cm / 2m channels using this X50 Diamond collinear 70/2  1m antenna at a height of 25m. I needed to investigate what could be wrong. Measuring the cable only 3W is left for the antenna of the 10W 435MHz output from a IC451E The cable is 30m type H100 Z50 10mm outside diameter it is semi air-spaced but has an impossible 4mm² solid CU inner conductor not much air left. I preferred the H43 Z75 cable having lower loss and mechanical better ratio in conductor size. My antenna uses SO239 connector UHF type semi air spaced isolator.  3W should be enough for a comfortable noise free FM signal. But only 27km away at PA0A the signal is weak too weak something must be wrong? I made a simple reference dipole of 2x17cm CU wire. With this dipole the signals where totally worse. So the Diamond does work? I got curious to look inside. Maybe moisture penetration degraded the antenna. This  antenna is rainwater close in its normal vertical mounting posit

SPF5189z Low noise preamp 23cm

 14-4-2018 updated Above the low noise  preamp 50 - 4GHz    ebay  6€ Tested  2 small porto antennas 1 Baofeng UV antenna left   2nd best signal on PI2NOS 2 eBay DIAMONDSRH805S  wide band 144/432/1200  it works for its size as expected 3 piece of wire :   best signal in the setup... Unit under test at workbench. It was stable  50mA  at 5V   few days,  but sudden the current went up to 100mA And i could  no longer adjust it with the negative bias Voltage. The - Voltage went to zero and the SPF input port became low Z. This SPF5189z was broken  no oscillations, no input overload just it broke while i was receiving the PI2NOS 430.125 using a small antenna at the workbench. The specs of  SPF5189z  say it has an internal circuit  regulating the bias current. Replaced . again   with an other of the 5 spare SPF i have. The new one again could be adjusted at 50mA  5V  The current raises to 150mA  when removing the  negative gate voltage. Where is that internal bias cir

BIJZEN mast en ontwerp fouten.

In 2013 heb ik een Bijzen aluminium mast 3 x7m  opgehaald  bij iemand die hem niet mocht plaatsen Gemeente Oss  dat zegt misschien al genoeg.. Pas in 2018 heb ik hem geplaatst had ik veel eerder moeten doen. Mooie mast, mijn xyl vond hem zelfs mooi. Hij is licht, de 3 delen wegen  235kg  het vaste deel 102kg dus het te lieren gedeelte weegt   slechts 133kg + ca 50kg rotor + antennes etc.  De elektrische lier is wel erg zwaar 30kg misschien wel maar die zit onder    Antenne  3ele Steppir  19kG  +  G2500DXC rotor: 3.6kg  + rotorbuis 12 kg  +  kabels 10kg  + 5/7 ele 6m beam. ongeveer 50kg Je moet niet te dichtbij  kijken, dan valt op dat het Aluminium lastwerk heel slordig is gedaan, scherpe bramen aan de lassen waar kabels door kunnen worden beschadigd of haken Er is zeer ! weinig ruimte voor de rotor een YAESU G2500DX past net maar dan ook net  met beetje buigen van  kruisverband. Het Rotor platform kan wel een meter hoger dat geeft meer  buislengte boven het zit nu op 3.5 meter van het